How to test/check Lab-Jack work condition , testing procedures of LabJack

Lab-jack testing procedure

Model no- U3 _HV

               

1.       Connect Cable laptop to Lab-jack

2.       Open software – LJ  control panel

 

              

 

 

3.       Select Model , click and find devices ( F3 )

4.       Then click on USB

5.       Lab-jack Model Number/ Serial Number  appear  on the NEW  window

6.       Cross check on Hardware ( Lab-jack )

7.       Check Default configuration




8.       Click on Test Tap.

 



 

9.        Pin details  check as per data sheets , and check functionality of each pin

10.   Using Multimeter , using different pin operation as per Data sheet

11.   If all pin work as per data sheet then ok

12.   Check supply on Lab-jack by multimeter

13.   Check output _ FIO Channel

14.   Select FIO4 , click Do

15.   Check on Hardware  FIO4-GND , should be 3.3 V , similar to other pin

16.   Check input , select input E.g._ AIN0, AIN1, AIN2, AIN3, connect to Ground , Voltage state should be Zero 0.0000 appear , similar to other pin

17.   Check 15 pin functionality, check voltage state according to data sheet with respect to pin number and GND , should be 3.3 V.

 

Thanks // Om prakash Gupta 


Comments

Post a Comment

Popular posts from this blog

Capacitor Bank , Power factor Improvement , why use Capacitor Bank

Image
Basic Power Factor Theory:   Power Factor compares the active power (kilowatts or kW) with apparent power (KVA) that is demanded from the power source. It is also a comparison of the active current to the total current, as shown in the triangle below. It is also equal to the cosine of the angle of displacement between the voltage and current waveform. The ratio of actual power to apparent power is usually expressed in percentage and is called power factor.   Generally the Transformers are inductive loads and cause very low power factor during their testing. Inductive equipment needs magnetizing power to produce the flux necessary for the operation of inductive devices. The unit of measure of magnetizing or reactive power is the kilovar (kVAR). The active power (kW) and reactive power (kVAR) together make up apparent power which is measured in kilovolt-amperes (kVA). By representing these components (kW and kVAR) of apparent power (kVA) as the sides of a right triangle, we can ...
Read more

NGEL is looking for experienced professionals for Renewable Energy area Government Jobs

Image
              NTPC NGEL ! Online Crash Course !  Government Job Preparation  !  NTPC Green Energy Limited (NGEL), a subsidiary of NTPC Ltd. has presence in the renewable power and hydrogen generation business. Commensurate with our country's growth challenges, the company has embarked upon an ambitious plan to attain a total installed capacity of 60 GW by 2032 Eligibility: RE (Electrical) Full Time 1 st  class B.Tech/B.E. in the area of Electrical Engineering. NGEL  Exam Pattern 2023 Candidates should be aware of NGEL Exam Pattern in order to have an understanding of the sectional weightage, exam duration etc. Details of the same are as follows: A total number of 120 questions are asked. The exam will be conducted for 120 marks. The duration of the examination is 2 hours. Subject No. of Qs. Max. Marks Professional Knowledge 60 60 General Awareness 15 15 English Language 15 15 Logical Reasoning 15 15 Quantitative ...
Read more

Transformer losses , online Transformer design course , transformer training courses in india , transformer course, online transformer design course in india , electrical design courses online , power transformer training course , transformer design teaching , transformer design training , electrical system design course , online technical Transformer Design course , online technical Transformer Design , Transformer design calculation excel, Transformer design calculator , online Transformer design calculation PDF , 3 phase transformer design calculation , 3-phase transformer design calculation pdf , Transformer winding calculation formula PDF, Transformer core size calculation, Transformer design softwareOnline electrical Transformer Course , online Transformer course, free online electrical courses with certificates, transformer training courses in india, power transformer training course ,udemy transformer design course online , online courses transformer design course in india, online classes Transformer designOnline Transformer design course , online Transformer design calculation course, online electrical Transformer Design Calculation course , online technical Transformer design course,

Image
  Transformer losses 1.       Core loss or Iron loss   a.       Hysteresis loss in transformer : Hysteresis loss is due to reversal of magnetization in the transformer core. This loss depends upon the volume and grade of the iron, frequency of magnetic reversals and value of flux density.   Steinmetz formula: W h = ηB max 1.6 fV (watts) where,   η = Steinmetz hysteresis constant              V = volume of the core in m 3                  F = Frequency   Energy loss in a transformer (Eddy current in the core )   b.       Ed dy current loss in transformer : In transformer, AC current is supplied to the primary winding which sets up alternating magnetizing flux. When this flux links with secondary winding, it produces induced emf in it. But some part of this flux also gets...
Read more